Updated November 2026

A 240v off grid solar system produces split-phase power for a home that runs 120V and 240V loads without a utility connection. In this guide you will learn how to size the array, battery bank and inverter, and how the 240V output is wired. The math is simple once you know the load numbers, and the wiring follows a fixed pattern.

Step 1: Calculate Your 240V and 120V Loads

Start by listing every appliance with its wattage and daily run time. Separate them into 120V loads (lights, outlets, electronics) and 240V loads (well pumps, electric dryers, heat pumps, range tops). Multiply watts by hours per day to get watt-hours, then total each group. Most homes that add a 240V circuit see the daily total jump quickly, so be honest about large loads.

Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).

Step 2: Size the Inverter for Split-Phase Output

A 240V off grid system uses a split-phase inverter that outputs two 120V legs 180 degrees apart, plus a neutral. This lets you run 240V appliances across both legs. Choose an inverter whose continuous rating covers your largest simultaneous load, and add a margin of roughly 25 percent. Check the surge rating too, because well pumps and compressors can draw two to three times their running wattage at startup. Confirm the inverter lists split-phase or 120/240V output before you buy.

Step 3: Size the Battery Bank and Solar Array

Divide your daily watt-hour total by the system voltage to get amp-hours per day. Multiply by the number of days of autonomy you want, usually one to two days, then divide by the usable depth of discharge. For lithium batteries that is often around 80 to 90 percent; for lead-acid it is closer to 50 percent. Size the solar array to replace the daily energy use after losses, which typically run 20 to 30 percent. Confirm the array’s peak wattage with your local peak sun hours.

Item How to calculate
Daily energy use Sum of watts × hours for all loads
Battery capacity (Ah) Daily Wh ÷ system voltage ÷ depth of discharge × days of autonomy
Array size (W) Daily Wh × 1.25 ÷ peak sun hours

Step 4: Wire the 240V Split-Phase Output

Connect the inverter’s two hot legs to a 240V breaker panel, with the neutral bonded to the panel’s neutral bar. Install a main breaker sized to the inverter’s output current, and use copper conductors rated for the circuit. Ground the system at a single point only, following the National Electrical Code (NEC) and your local inspector’s requirements. Bonding the neutral in more than one place is a common and dangerous error. For a full diagram, see Wiring Diagram for Off-Grid Solar System: A Step-by-Step Guide.

Common Mistakes to Avoid

  • Sizing the inverter only for average load and ignoring motor startup surge.
  • Bonding neutral and ground at both the inverter and the panel.
  • Undersizing battery cables, which causes voltage drop and heat.
  • Forgetting to include a generator input or charge source for cloudy stretches.
  • Skipping a permit and inspection, which can complicate insurance and resale.
  • Split-phase hybrid inverter: Converts battery and array power into 120/240V output for mixed loads. View on Amazon
  • Lithium iron phosphate battery bank: Offers high usable depth of discharge, which keeps the bank smaller. View on Amazon
  • MC4 solar extension cables: Let you route array strings to the inverter without field splicing. View on Amazon

FAQ

Can a 240V off grid system run an electric dryer?

Yes, if the inverter’s continuous and surge ratings cover the dryer’s heating element draw and the battery bank can supply it. Electric dryers are among the heaviest loads, so many owners limit dryer use to sunny hours.

Do I need a generator with a 240V off grid system?

Not always, but a generator input is useful for winter or extended cloudy periods. Many split-phase inverters accept a generator as a secondary charge source.

Is a 240V off grid system the same as a grid-tied system?

No. An off grid system stores energy in batteries and works without the utility, while a grid-tied system exports to the grid. For the differences, read Solar Grid Tie System vs Off Grid: Which Should You Choose?.

Conclusion

A 240v off grid solar system works when the loads, inverter, battery bank and array are sized together from the same daily energy number. Follow the steps above, check surge ratings, and bond the neutral at one point only. Have a licensed electrician or your local inspector review the final design before you energize it.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our DIY solar power systems guides, checking product details against manufacturer specifications and owner feedback.