Updated November 2026
A lifepo4 battery voltage chart lets you estimate how full a LiFePO4 pack is by reading its terminal voltage. This guide gives you the reference values for 12V, 24V and 48V nominal banks, explains why readings change with load and temperature, and shows you how to take a reading that actually means something. Treat the numbers as estimates, not a fuel gauge.
Reference Voltages for 12V, 24V and 48V Packs
LiFePO4 cells have a famously flat discharge curve. Most of the capacity is delivered between roughly 3.2V and 3.3V per cell, so the voltage barely moves across the middle of the charge range. That is why a voltage chart is less precise than it is for lead-acid. The values below are approximate resting voltages for a 4-cell (12V), 8-cell (24V) and 16-cell (48V) pack at about 25°C after the battery has rested for several hours.
Shopping for one? See our guide: EcoFlow 12V 100Ah LiFePO4 Battery Review: Strengths and Limitations.
| State of charge | Per cell (V) | 12V pack (4S) | 24V pack (8S) | 48V pack (16S) |
|---|---|---|---|---|
| 100% | 3.40–3.45 | 13.6–13.8 | 27.2–27.6 | 54.4–55.2 |
| 90% | 3.35 | 13.4 | 26.8 | 53.6 |
| 80% | 3.33 | 13.3 | 26.6 | 53.2 |
| 50% | 3.28 | 13.1 | 26.2 | 52.5 |
| 20% | 3.22 | 12.9 | 25.8 | 51.5 |
| 10% | 3.00–3.10 | 12.0–12.4 | 24.0–24.8 | 48.0–49.6 |
| 0% (cutoff) | 2.50–2.80 | 10.0–11.2 | 20.0–22.4 | 40.0–44.8 |
Values near the bottom of the table drop quickly, so a low-voltage cutoff set to protect the cells usually sits around 10% state of charge, not 0%. Always confirm the exact cutoff in the battery manufacturer’s specifications, since BMS settings vary.
How to Take a Reading You Can Trust
A voltage reading is only useful if the battery is near rest. Follow these steps to get a number that maps onto the chart:
- Disconnect all loads and chargers, then wait at least two to three hours. Overnight is better.
- Measure directly across the main positive and negative terminals with a multimeter set to DC volts.
- Note the battery temperature. Cold packs read lower than their true state of charge.
- Compare the reading to the 12V, 24V or 48V column above.
Why Readings Change Under Load and Charge
Under a heavy discharge, voltage sags because of internal resistance. Under charging, it rises above the resting value. A pack reading 13.2V while a 30-amp load is running may be near 60% charge, while the same pack reads 13.4V at rest. Charging to 14.2V to 14.6V is typical for a LiFePO4 bulk stage, and the reading will fall back toward the chart once the charger stops.
Temperature Effects
Cold temperatures reduce usable capacity and make voltage readings less reliable. Many LiFePO4 batteries block charging below about 0°C, so check the manufacturer’s temperature limits before assuming a low reading means a dead pack.
Common Mistakes
- Reading voltage immediately after charging or discharging, which inflates or deflates the result.
- Assuming a lead-acid chart applies. LiFePO4 voltages sit higher at full and stay flat through the middle.
- Using the chart on a pack where cells have drifted out of balance. Check individual cell voltages with the BMS if available.
- Treating 0% as the safe floor. Stopping discharge near 10% extends cycle life.
- Ignoring temperature when cold weather pushes readings down.
Recommended gear
A basic digital multimeter with a DC voltage range is all you need for spot checks. For ongoing monitoring, a battery monitor shunt gives you state of charge based on amp-hour tracking, which is more accurate than voltage alone. View on Amazon
If you are setting up charging and want to match voltages correctly, a dedicated LiFePO4-profile charger removes guesswork about absorption and float targets. View on Amazon
For sizing and charging details beyond the chart, see Charging a LiFePO4 Battery: Voltages, Current Limits and Setup Steps and How to Size a Solar Battery Bank: Autonomy, Depth of Discharge and Voltage. Builders working with a specific pack may also find Redodo 12V 100Ah LiFePO4 Battery: Sizing, Wiring and Setup Guide useful.
FAQ
Is a LiFePO4 battery full at 13.6V?
A 12V LiFePO4 pack at about 13.6V at rest is close to full, typically around 100% state of charge. Confirm with a rested reading, since charging voltage is higher than resting voltage.
What voltage is a LiFePO4 battery empty?
Most builders treat about 10% state of charge as empty, roughly 12.0V to 12.4V for a 12V pack at rest. Going lower risks damaging cells and triggering the BMS cutoff.
Can I use a lead-acid voltage chart for LiFePO4?
No. Lead-acid charts show a steep drop across the charge range, while LiFePO4 stays nearly flat through the middle. Using a lead-acid chart will badly misjudge capacity.
Conclusion
A lifepo4 battery voltage chart is most useful when you read the pack at rest, after several hours without load or charge, and correct for temperature. Use the 12V, 24V or 48V column to estimate state of charge, and remember the curve is flat, so pair voltage with amp-hour tracking for better accuracy. Consult the battery manufacturer’s specifications for exact limits.
