Updated November 2026
An off grid solar system sizing calculator is simply a set of steps that turns your daily electricity use into panel wattage, battery capacity and inverter size. In this guide you will total your loads, calculate your daily energy need, and size each major component with the math shown. The method works for cabins, sheds and full homes alike.
Step 1: List Every Load and Its Daily Run Time
Start with an appliance inventory. For each device, note its wattage (usually printed on the label or in the manual) and how many hours per day it runs. Refrigerators cycle, so use the average running time, often around 8 to 10 hours per day for a modern unit. Multiply watts by hours to get watt-hours (Wh) per day for each load, then add them together.
Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).
Example: a 60 W LED light running 5 hours uses 300 Wh. A 150 W laptop running 4 hours uses 600 Wh. Add all loads to get your total daily energy need.
Step 2: Adjust for Losses and Set Your Battery Bank Size
Real systems lose energy in wiring, the inverter and the charge controller. Multiply your daily total by 1.2 as a practical allowance. Then decide how many days of autonomy you want, meaning how long the batteries can run the loads with no sun. Two days is a common starting point.
Battery capacity (Ah) = (Daily Wh × Autonomy days) ÷ (Battery voltage × Depth of discharge). For lead-acid batteries, a depth of discharge of 0.5 is typical. For lithium iron phosphate, many manufacturers specify 0.8 to 0.9. Example: 1,440 Wh × 2 days ÷ (48 V × 0.5) = 120 Ah at 48 V.
Step 3: Size the Solar Array
Divide your daily energy need (with the 1.2 allowance) by your location’s peak sun hours, which you can look up on NREL’s solar resource maps. Then add a charging efficiency factor of about 0.75 to cover temperature, dust and controller losses.
Panel wattage = Daily Wh × 1.2 ÷ (Peak sun hours × 0.75). If your daily need is 1,440 Wh and you get 4 peak sun hours, the array needs about 480 W. Round up to the next practical panel combination.
Step 4: Choose the Charge Controller and Inverter
The charge controller must handle the array’s current. Divide total panel wattage by battery voltage, then add a 25% margin. For 480 W on a 48 V system, that is about 12.5 A, so a 15 A or larger controller is appropriate. MPPT controllers are generally better suited to arrays with higher voltage than the battery.
For the inverter, add the wattage of loads that might run at the same time, then add a 25% margin. Pay attention to surge ratings for motors and compressors, which can be several times running wattage at startup.
Quick Sizing Checklist
- Inventory all loads with watts and hours per day.
- Total daily Wh and multiply by 1.2.
- Calculate battery Ah using autonomy days and depth of discharge.
- Calculate array watts using peak sun hours and 0.75 efficiency.
- Size the controller current with a 25% margin.
- Size the inverter for simultaneous peak load plus surge.
| Component | Formula | Example Result |
|---|---|---|
| Daily energy | Sum of watts × hours × 1.2 | 1,440 Wh |
| Battery bank | Wh × days ÷ (V × DoD) | 120 Ah at 48 V |
| Solar array | Wh ÷ (sun hours × 0.75) | About 480 W |
Common Mistakes to Avoid
- Using nameplate wattage instead of measured or average running time.
- Forgetting phantom loads from inverters, chargers and standby electronics.
- Sizing the battery without accounting for depth of discharge.
- Ignoring winter sun hours, which can be far lower than summer values.
- Skipping the surge rating when choosing an inverter for motors.
Recommended Gear
A plug-in power meter helps you measure real appliance consumption instead of guessing, which tightens your daily Wh total. View on Amazon
A clamp-style multimeter lets you check actual battery and array current during commissioning. View on Amazon
FAQ
How many solar panels do I need for an off grid system?
Divide your daily watt-hour need by your peak sun hours and a 0.75 efficiency factor. The result is the total array wattage, which you then divide by your panel rating to get the panel count.
What autonomy should I design for?
Two days is a common target for most homes, because it covers a typical stretch of cloudy weather. Critical loads like medical equipment may justify more.
Should I consult a professional?
Yes, especially for systems powering a full home or connecting to a main panel. A licensed electrician or solar installer should verify wiring, grounding and code compliance before you energize the system.
Conclusion
Using this off grid solar system sizing calculator method, you can move from a rough guess to a defensible set of battery, array, controller and inverter sizes. Once you have your numbers, compare them with the detailed build walkthroughs on this site, such as Planning an Off-Grid Solar System: 8 Steps to Size It Right and Off Grid Solar Power System Calculator: How to Size Your Setup Step-by-Step. Double-check your math with a second method before buying equipment.
