Updated November 2026
A DIY solar cover reel lets you roll a solar pool cover onto a spool, keeping it off the deck and out of the way until you need it. You will learn how to measure the cover, pick a reel size, build a simple frame, and set up a crank or hand-drive that stays stable under load. The whole build uses common hardware-store parts and takes a weekend for most DIYers.
Measure the Cover and Size the Reel
Start with the cover’s width and length, not its area. The reel barrel must be wide enough to hold the full width of the cover, and its diameter determines how many turns it takes to roll the whole length. A common target is a barrel diameter of 6 to 8 inches, which keeps the bending radius gentle enough that the cover does not crease or crack. Check the cover manufacturer’s minimum bend radius if one is listed, and avoid going smaller.
Shopping for one? See our guide: 7 Best DIY Solar Patio Covers for Backyards and Decks (2026).
Next, calculate the roll diameter when fully wound. Each wrap adds roughly the cover’s thickness, so a 20-foot cover of typical bubble-material thickness will build a roll several inches across. Make sure the frame clears the pool deck or patio when the roll is full.
Build the Frame and Barrel
Use schedule 40 PVC or galvanized steel pipe for the barrel. Cut it to the cover width plus about 2 inches for end caps. Mount the barrel on two bearing-style pillow blocks or through-hole supports attached to a rigid base, such as pressure-treated 4×4 posts or a steel angle frame. The barrel must spin freely, so align both supports carefully. A misaligned barrel will drag the cover to one side.
- Cut the barrel to length and deburr both ends.
- Drill and attach end caps or a central axle that passes through the barrel.
- Mount the supports so the axle sits level and parallel to the pool edge.
- Attach a crank handle or a gear-reduction drive to one end of the axle.
- Fasten the cover’s leading edge to the barrel with a stainless clamp bar or sturdy self-tapping screws through reinforced webbing.
- Test the reel by rolling and unrolling the cover slowly, checking for even tension.
Add a Braking or Locking Mechanism
A reel without a brake will unwind under wind or gravity. Install a ratchet pawl on a gear wheel, or a simple friction brake using a pivoting arm and a rubber pad. The brake should hold the cover in place when you let go of the crank. Test it with a light wind before leaving the cover unattended.
Materials and Tools Checklist
- Barrel pipe (PVC or galvanized steel), cut to cover width plus 2 inches
- Two pillow block bearings or pipe supports
- Pressure-treated lumber or steel angle for the base
- Axle rod, end caps, and set screws
- Crank handle or gear reducer with ratchet brake
- Stainless steel fasteners and clamp bar
- Drill, level, tape measure, and socket set
Common Mistakes to Avoid
- Using a barrel that is too small, which can crease or tear the cover.
- Skipping the brake, leading to uncontrolled unrolling in wind.
- Misaligned supports that cause the cover to walk sideways.
- Attaching the cover with fasteners that pull through the material.
- Building a base that flexes under a full, heavy roll.
Recommended Gear
Stainless clamp bars reduce tearing where the cover attaches to the barrel, and they are easy to replace if the fastening point wears. A pillow block bearing kit gives smoother rotation than bare pipe holes, which helps prevent binding. A ratchet and pawl kit designed for winch-style drives can supply reliable braking without custom machining.
FAQ
Can I use a DIY solar cover reel on an above-ground pool?
Yes, as long as the reel base is anchored firmly and sized to the cover width. Above-ground pools often need a shorter barrel and a lower-profile frame to fit beside the wall.
What material works best for the reel barrel?
PVC is light and corrosion-resistant, while galvanized steel is stiffer and better for wide covers. Either works if the barrel is sized correctly and supported at both ends.
How do I keep the cover from unrolling in wind?
Use a ratchet or friction brake on the crank side, and lock the reel whenever the cover is stored. Check the brake periodically, since wear can reduce holding strength over time.
Conclusion
A well-sized barrel, aligned supports, and a dependable brake are the three factors that make a DIY solar cover reel work reliably. Measure carefully, build the frame square, and test the reel before trusting it. Consult a professional for structural or electrical questions about the surrounding installation.
Related reading
- DIY Solar Blanket Reel: How to Build a Portable Roll-Up Panel System
- 5 Best DIY Solar Cover Holders for Above Ground Pools (2026)
- Top 7 DIY Solar Powered Oven Options Compared for Backyard Cooking
- Top 7 DIY Solar Power Fan Options Compared for Sheds and Coops
- Top 7 DIY Solar Panel Installation Kit Options Compared for Beginners
