Updated November 2026
Solar eclipse glasses DIY projects come down to one thing: building a viewer that uses certified solar filter material and fits your face snugly. This guide walks you through choosing the right filter, cutting and mounting it, and checking your finished pair before you look at the sun. Done correctly, you will have a safe, inexpensive way to watch a partial eclipse.
Why Only Certified Filter Material Works
Ordinary sunglasses, exposed photographic negatives, smoked glass and welding goggles below shade 12 do not block enough sunlight to protect your eyes. Only filters that meet the ISO 12312-2 standard reduce sunlight to a safe level. Look for that marking on the filter material itself or on the packaging, and buy from a source that identifies the manufacturer. If a seller cannot confirm the standard, do not use the material.
Shopping for one? See our guide: 6 Best DIY Solar PV Panel Kits for Off-Grid Builds (2026). 5 Best DIY Solar Generators for Home Backup Picks Compared (2026) goes further into this.
Step-by-Step: Building Your Viewer
- Choose a frame. Cardboard from a cereal box or a sheet of thin card works well. A 4-inch by 6-inch piece gives enough room for two eyeholes spaced about 2.5 inches apart, which matches most adult faces.
- Cut the eyeholes. Trace the outline of your eyes and cut them about 1/4 inch larger than the sockets, so the filter does not press against your eyelashes.
- Cut the filter. Cut the certified film about 1/2 inch larger on every side than each eyehole. Oversized film prevents light from leaking around the edges.
- Tape the film in place. Apply a continuous strip of tape around the inside edge of each opening, sealing the filter fully. Avoid gaps; any uncovered gap is an unfiltered path to your eye.
- Inspect before use. Hold the viewer toward a bright lamp indoors. Light should be dim and even through the film, with no bright spots, pinholes or wrinkles.
Materials Checklist
- ISO 12312-2 certified solar filter film, enough for two eyeholes with margin
- Sturdy card or cardboard
- Scissors or a craft knife with a cutting mat
- Black electrical tape or painter’s tape
- Pencil and ruler for marking
Testing and Fit Checks
A homemade viewer should fit flush against your face so no sunlight enters from the sides or top. Test in daylight before the eclipse by pointing the viewer at a bright sky, not the sun. Make sure you can see only a uniform, dim image. If the film wrinkles or the tape lifts, replace the piece rather than patching it. Keep the viewer out of direct sunlight between uses if you plan to reuse it.
Common Mistakes
- Using a single layer of sunglasses or tinted plastic as a substitute for certified film.
- Leaving gaps between the filter and the card, which let unfiltered light reach your eyes.
- Looking at the sun through a camera, phone or binoculars without a separate solar filter on the lens.
- Checking the filter only once and not inspecting it again after handling.
- Viewing during totality without a filter. Totality is the only brief period when the sun is fully covered, and it is the only time it is safe to look directly without protection, but outside totality you must always use filtered viewing.
Recommended Gear
Certified solar filter film is the single most important item, since it is the component that actually protects your eyes. A sturdy card or cutting mat makes accurate eyeholes easier to achieve. For photographing the eclipse, a separate solar filter for the lens is required, not a homemade viewer.
- ISO-certified solar viewing film sheets for DIY eyewear: the core protective material for any homemade viewer. View on Amazon
- Self-healing cutting mat: keeps your card flat and protects the table while you cut clean eyeholes. View on Amazon
- Precision craft knife with replacement blades: gives cleaner edges than scissors when trimming film and card. View on Amazon
FAQ
Can I make solar eclipse glasses DIY from sunglasses?
No. Sunglasses, even dark ones, do not block enough sunlight to protect your eyes from solar damage. Only ISO 12312-2 certified filter material is safe for direct solar viewing.
How do I know if my homemade filter is safe?
Confirm the film carries the ISO 12312-2 marking, then check that it fully covers each eyehole without gaps or pinholes. The view through it should be dim and uniform when pointed at a bright sky.
Is a DIY viewer safe for children?
Children should use a viewer only under adult supervision, and they should be taught never to remove the viewer to look at the sun. If you have concerns about eye safety, consult an eye care professional.
Conclusion
A well-built solar eclipse glasses DIY viewer uses certified filter film, seals every edge and passes a light-leak check before use. Always inspect your viewer before each viewing session. When in doubt about eye safety, consult an eye care professional before looking at the sun.
