Updated November 2026

An off-grid solar system calculation tells you how many panels, how much battery storage and what inverter capacity you need to run your home without the utility. In this guide you will total your daily energy use, size the battery bank, work out the panel array and check the inverter and charge controller. The math is simple arithmetic, but every number should be checked against real loads.

Step 1: Calculate Your Daily Energy Use in Watt-Hours

Start with your loads. List every appliance you plan to run, its power rating in watts and how many hours per day it runs. Multiply watts by hours to get watt-hours (Wh) per day, then add the column together.

Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).

For example, a 60 W LED light running 5 hours uses 300 Wh per day. A 100 W laptop running 4 hours uses 400 Wh. Add a 10 to 20 percent margin to cover losses and loads you forgot. Your total is your daily load in Wh.

Step 2: Size the Battery Bank

Battery capacity is where most off-grid systems fail, so size it for the days you get the least sun, not the average day. Divide your daily load by the battery system voltage to get amp-hours (Ah), then multiply by the number of days of autonomy you want (usually 2 to 3 days).

Next, account for depth of discharge. Lead-acid batteries are normally limited to about 50 percent discharge, while lithium iron phosphate (LiFePO4) batteries are often rated for 80 to 90 percent. Divide the required Ah by your usable depth of discharge to get the nominal bank size.

Example: 3,000 Wh per day at 24 V is 125 Ah per day. Two days of autonomy gives 250 Ah. With LiFePO4 at 90 percent usable, you need about 278 Ah nominal.

Step 3: Work Out the Solar Panel Array

Panel sizing depends on peak sun hours at your location, which you can find in NREL or local solar resource maps. Use the lowest winter value for a reliable system.

  1. Divide daily load (Wh) by peak sun hours to get the required panel wattage.
  2. Add 20 to 30 percent for charge controller, wiring and battery charging losses.
  3. Divide the total by the wattage of one panel to find the panel count.

Example: 3,000 Wh per day with 3.5 peak sun hours gives 857 W. Add 25 percent to reach about 1,070 W, which is roughly four 300 W panels.

Step 4: Choose the Inverter and Charge Controller

The inverter must handle your largest combined load, plus surge current from motors and compressors. Choose a continuous rating at least 25 percent above your peak simultaneous load. The charge controller must handle the array’s short-circuit current at your battery voltage. Size the controller current as array watts divided by battery voltage, then add a safety margin.

For a deeper walkthrough of the full build, see Planning an Off-Grid Solar System: 8 Steps to Size It Right and Solar Off-Grid System Design Calculation PDF: A Step-by-Step Guide.

  • A clamp meter or plug-in watt meter helps you measure real appliance draw rather than relying on nameplate ratings. View on Amazon
  • A solar charge controller with an LCD display lets you watch array input and battery state while you test the system. View on Amazon

Common mistakes

  • Sizing panels on summer sun hours and then running short in winter.
  • Ignoring inverter standby draw, which can add tens of watt-hours a day.
  • Using nameplate watts instead of measured running watts for motors.
  • Forgetting battery depth-of-discharge limits and the round-trip efficiency of charging.
  • Skipping a margin for future loads or cloudy weeks.

FAQ

How many solar panels do I need for an off-grid house?

It depends on your daily watt-hour use and local peak sun hours. Most homes need several hundred to a few thousand watts of panels, calculated using the steps above.

Should I size the battery for one day or several days?

Most designers plan for two to three days of autonomy so the system survives cloudy weather. A single day of storage is usually too little for reliable off-grid power.

Can I use this calculation for a small cabin?

Yes, the same method works at any scale. Only the load numbers change, so a cabin with a few lights and a fridge will need far smaller components. Consult a licensed electrician for wiring and permits.

Conclusion

An off-grid solar system calculation follows four steps: total your daily watt-hours, size the battery bank with autonomy and depth of discharge, work out the panel array with peak sun hours and losses, then match the inverter and charge controller. Verify your numbers against measured loads before you buy. Have a professional review any system that connects to your home wiring.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our DIY solar power systems guides, checking product details against manufacturer specifications and owner feedback.