Updated November 2026

Building an off grid solar system means producing and storing all the electricity your home uses, with no utility connection to fall back on. In this guide you will learn how to estimate your daily energy use, size the panels, battery bank and inverter, and wire the components in the right order. The math is simple once you have your load numbers, and those numbers drive every other decision.

Step 1: Calculate Your Daily Energy Load

Start with a list of every device you plan to run, its wattage, and how many hours per day it runs. Multiply watts by hours to get watt-hours (Wh), then add everything up. A 60 W refrigerator running 10 hours a day is 600 Wh, while a 1,000 W microwave running 0.2 hours is 200 Wh. Many owners add a 20 to 30 percent margin for cloudy days and appliances that draw more than their label suggests.

Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).

Step 2: Size the Battery Bank and Solar Array

Divide your daily load by the battery system voltage to get amp-hours per day, then multiply by the number of days of autonomy you want (often two or three). Divide again by the usable depth of discharge: lithium iron phosphate batteries are commonly rated for about 80 to 90 percent usable capacity, while flooded lead-acid is usually limited to about 50 percent. For the array, divide daily watt-hours by your location’s peak sun hours. If your load is 3,000 Wh and you get 4 peak sun hours, you need roughly 750 W of panels before accounting for system losses. Most designers add 25 percent more to cover inefficiency, which puts that example near 940 W.

Step 3: Choose the Charge Controller and Inverter

The charge controller must handle the array’s current at your battery voltage. An MPPT controller is generally the better match for larger arrays because it converts excess panel voltage into charging current. The inverter should be rated for your largest simultaneous load, with headroom for motor startup surges from pumps or compressors. The guide to Wiring Diagram for Off-Grid Solar System: A Step-by-Step Guide shows how these parts connect.

Step 4: Wire the System in the Correct Order

Wire the components in this sequence: panels to the charge controller, controller to the battery bank, and inverter to the battery bank. Connect the inverter to the battery bank last, and disconnect in reverse. Fuse or breaker every positive conductor close to the battery, and size conductors for the expected current over the run length. Use the manufacturer’s torque specs on terminals.

  1. Mount panels and run cable to the controller location.
  2. Install the controller and connect it to the battery bank with an appropriately sized fuse.
  3. Connect the inverter to the battery bank with its own fuse or breaker.
  4. Add a main disconnect and a grounding system per local code.
  5. Power up in order: battery, controller, then inverter.

Common Mistakes to Avoid

  • Sizing from the appliance nameplate instead of measured or realistic run times.
  • Ignoring winter sun hours, which can be less than half of summer values.
  • Undersized wire causing voltage drop and heat at high current.
  • Skipping fuses or using the wrong type for DC circuits.
  • Choosing an inverter that cannot handle motor startup surges.
  • Clamp-style DC multimeter: lets you measure panel current and battery voltage without disconnecting wires. View on Amazon
  • Inline DC fuse holders and fuses: protect battery cables at the point of connection. View on Amazon
  • Crimping tool for ring and spade terminals: reliable crimps are essential for high-current DC cable. View on Amazon

FAQ

How many solar panels do I need for an off-grid home?

It depends on your daily watt-hour use and local peak sun hours. Divide daily load by peak sun hours, then add about 25 percent for system losses.

Do I need a battery bank for an off-grid system?

Yes. Without batteries, power is only available while the sun is shining, so storage is required for nighttime and cloudy-day use.

Should a DIYer attempt the electrical work alone?

Basic wiring is manageable for careful beginners, but a licensed electrician should review the design and inspect the installation, especially for grounding and permits.

Conclusion

A well-built off grid system starts with an accurate load estimate and grows from there. Size the batteries and array from that number, choose a controller and inverter that match, and wire everything in the correct order with proper fusing. Take the time to get the math right before buying hardware.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our DIY solar power systems guides, checking product details against manufacturer specifications and owner feedback.