Updated November 2026

An off-grid solar system calculator, whether it lives in an Excel spreadsheet or a printable PDF, turns your daily energy use into panel, battery and inverter sizes. In this guide you will learn the inputs a sizing sheet needs, the formulas behind each result, and how to check the output before you buy anything. The method works the same whether you build the sheet yourself or download a template.

Gather Your Load Data First

Every calculation starts with how much energy you use per day, measured in watt-hours (Wh). List each appliance, its wattage, and how many hours it runs daily. Multiply watts by hours to get Wh per day, then add the totals.

Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).

  • Refrigerator: often 100 to 200 Wh/day, depending on size and efficiency
  • LED lighting: a few watts per fixture, several hours each
  • Laptop or router: small loads that add up over a full day
  • Well pump or power tools: high surge loads that the inverter must handle

Add a 20 to 25 percent margin to the daily total to cover losses and future additions.

Size the Battery Bank and Inverter

Battery capacity in amp-hours (Ah) is calculated from daily Wh, system voltage, days of autonomy (how many cloudy days you want to ride through), and the usable depth of discharge. A common formula is: We also found 3 Best Solar Power Generator Inverter Options for Home and Off-Grid Use useful on this point.

Battery Ah = (Daily Wh × Autonomy days) ÷ (System Volts × Depth of Discharge)

For example, 3,000 Wh per day, 2 days of autonomy, a 24-volt system and 50 percent depth of discharge gives 3,000 × 2 ÷ (24 × 0.5) = 500 Ah. Manufacturers of lithium batteries often specify a higher usable depth, which lowers the required Ah. Choose the inverter based on your peak running load, with headroom above your largest simultaneous draw and enough surge rating for motors.

Calculate Panel Array Size

Panel wattage depends on your daily energy need and the peak sun hours at your location. Use a conservative figure for your worst winter month, not the annual average.

Array Watts = (Daily Wh ÷ Peak Sun Hours) × Loss Factor

A loss factor of about 1.3 accounts for wiring, temperature, dust and charge controller losses. If your daily load is 3,000 Wh, winter sun hours are 3, and the loss factor is 1.3, you need roughly 1,300 W of panels. Round up to the next practical panel count.

Check Charge Controller Current

Divide total array watts by battery voltage to get the controller’s required current. Add 25 percent as a safety margin. For 1,300 W on a 24-volt bank, that is about 68 amps, so a 70 to 80 amp controller would fit.

A few supporting items make the sizing sheet’s results easier to put into practice.

  • Clamp meter: confirms real appliance draw so your load list matches reality. View on Amazon
  • Digital multimeter: lets you verify voltages across the battery bank and array before connecting loads. View on Amazon

Common Mistakes to Avoid

  • Using annual average sun hours instead of the worst winter month.
  • Forgetting inverter efficiency, which typically runs around 85 to 90 percent.
  • Ignoring surge loads from pumps and compressors.
  • Entering battery capacity at its rated Ah without applying depth of discharge.
  • Skipping the loss factor, which leaves the array undersized on cloudy days.

To see the full workflow, read Off-Grid Solar System Calculator Excel: Build Your Own Sizing Sheet for spreadsheet formulas, and Solar Off-Grid System Design Calculation PDF: A Step-by-Step Guide for a printable version of the same math.

FAQ

Is an Excel sizing sheet as accurate as a professional design?

An Excel sheet gives a sound first estimate if your load data and sun hours are accurate. A licensed installer should review the final design, especially for battery banks and wiring.

What peak sun hours should I use?

Use the lowest monthly average for your location, typically from a solar resource map or the NREL PVWatts tool. Sizing to winter conditions prevents shortfalls.

Can I use a PDF calculator instead of a spreadsheet?

Yes. A PDF works for quick checks, but a spreadsheet lets you change inputs and compare scenarios. Either one will produce the same results if the formulas are right.

Conclusion

A reliable off-grid solar system calculator in Excel or PDF form depends on careful load data, realistic sun hours and correct battery math. Work through each step in order, apply the loss factor, and double-check the results. Consult a qualified professional before final installation.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our DIY solar power systems guides, checking product details against manufacturer specifications and owner feedback.