Updated November 2026

An off grid solar power system design calculator turns your daily power use into the panel wattage, battery capacity and inverter size you need. In this guide you will total your loads, convert them into daily watt-hours, and work backward to a sized array and battery bank. The math is simple arithmetic, and you can run it on paper or in a spreadsheet.

Step 1: Total Your Daily Energy Use

Start by listing every appliance you plan to run, its wattage, and how many hours per day it operates. Multiply watts by hours to get watt-hours (Wh) per day. A 60 W fan running 8 hours uses 480 Wh. Add all the values together to get your total daily load. Include a margin of about 20 percent for losses in wiring, inverter conversion and battery charging.

Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).

Step 2: Size the Battery Bank

Battery capacity depends on how many days of autonomy you want, meaning how long the system can run without sun. Multiply your daily load by the number of autonomy days, then divide by the usable depth of discharge. For lead-acid batteries, a common planning figure is 50 percent. For lithium iron phosphate, manufacturers often specify 80 to 90 percent. Divide the result by your battery voltage to get amp-hours (Ah). A 4,800 Wh daily load with two days of autonomy at 80 percent depth of discharge needs 12,000 Wh, or about 1,000 Ah at 12 V.

Step 3: Calculate the Solar Array Size

Divide your daily load, with losses included, by your location’s peak sun hours. Peak sun hours are the equivalent hours per day at full sunlight, and they vary by season and latitude. Then divide that number by the panel’s real output after accounting for system derating, which is commonly estimated around 75 percent. The result is your total array wattage. Divide that by the wattage of the panel you plan to buy to find the panel count.

  1. Daily load (Wh) × 1.2 for losses
  2. Divide by peak sun hours
  3. Divide by derate factor (about 0.75)
  4. Divide by panel wattage to get panel count

Step 4: Choose the Inverter and Charge Controller

Size the inverter to handle your highest combined simultaneous load, plus a surge margin for motors such as well pumps or refrigerators. A common approach is to choose an inverter rated at least 25 percent above your peak continuous draw. The charge controller must handle the array’s maximum current. Check the controller’s voltage and amperage ratings against your array’s open-circuit voltage and short-circuit current, not just nameplate watts.

Common Mistakes

  • Using average sun hours from a summer month only, which leaves the system short in winter.
  • Forgetting standby loads from inverters, routers and chargers.
  • Ignoring battery depth of discharge and sizing by total capacity alone.
  • Oversizing the array without checking that the charge controller can handle the current.
  • Skipping the loss margin, which makes real-world performance fall short of the math.
  • Kill A Watt power meter helps you measure the real draw of each appliance instead of relying on label wattage. View on Amazon
  • Victron Energy SmartSolar MPPT charge controller is widely used in DIY builds and offers Bluetooth monitoring for checking array performance. View on Amazon

FAQ

How many solar panels do I need for an off-grid home?

It depends on your daily watt-hour use and local peak sun hours. Most homes need between a few kilowatts and over ten kilowatts of panels, and the calculator steps above will give you your exact count.

What is peak sun hours?

Peak sun hours are the equivalent number of hours per day when sunlight averages 1,000 watts per square meter. Your location’s solar resource maps or local tables provide this figure, and it changes by season.

Should I size for winter or summer?

Size for the worst month, which is usually winter in most of the US. A system sized only for summer will often fall short during the months when you need it most. Consult a licensed electrician before connecting any system to your home’s wiring.

Conclusion

Total your daily watt-hours, size the battery bank for your autonomy days, and divide by peak sun hours to get your array. Check the inverter and charge controller against your peak loads and array specs. Work through these numbers before buying equipment, and see Off-Grid Solar Power System Calculator: How to Size Your Setup Step-by-Step for a worked example.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our DIY solar power systems guides, checking product details against manufacturer specifications and owner feedback.