Updated November 2026

An off grid solar system design calculator turns your daily energy use into a panel count, battery bank size and inverter rating. This guide walks you through the math step by step, so you can build a sizing sheet you trust before you buy a single part. Every number below comes from the same basic formulas used across most off-grid planning tools.

Step 1: Total Your Daily Energy Use in Watt-Hours

List every appliance you plan to run, its wattage, and how many hours per day it operates. Multiply watts by hours to get watt-hours (Wh) per day. A 60 W fan running 8 hours uses 480 Wh. A 100 W laptop running 4 hours uses 400 Wh. Add everything together for your daily load. Include a 10 to 20 percent margin for losses in wiring, the inverter and the battery.

Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).

Step 2: Size the Battery Bank

Battery capacity is where most DIY sizing goes wrong. Start with your daily Wh, then decide how many days of autonomy you want, usually one to three days for cloudy weather. Divide the total by your system voltage (often 12, 24 or 48 V) to get amp-hours (Ah). Then account for depth of discharge. Lead-acid batteries are commonly limited to about 50 percent use, while lithium iron phosphate (LiFePO4) batteries are often rated for 80 to 90 percent.

For example, 4,800 Wh per day, two days of autonomy, a 48 V system and 80 percent depth of discharge gives 9,600 Wh divided by 48 V, then divided by 0.8. That works out to about 250 Ah at 48 V.

Step 3: Calculate the Solar Array Size

Divide your daily load by the peak sun hours at your location, then add a loss factor. Peak sun hours are published in solar irradiance maps for most regions, and winter values are the ones to design around. Use a system efficiency of about 0.75 to cover charge controller, wiring and temperature losses.

Using the same 4,800 Wh per day load, 4 peak sun hours and 0.75 efficiency: 4,800 divided by 4 divided by 0.75 gives about 1,600 W of panels. A 1,600 W array would use roughly six 275 W panels.

Step 4: Choose the Inverter and Charge Controller

Your inverter must handle the sum of simultaneous loads, plus a surge margin for motors and compressors. Most designers size the continuous rating at 125 percent of expected peak load. The charge controller must handle the array’s short-circuit current. Divide total panel wattage by system voltage, then multiply by 1.25 for a safe controller current rating.

A clamp-on power meter helps you verify real daily loads before you commit to a design, which is more accurate than appliance labels. View on Amazon

A multimeter lets you check open-circuit voltage on panels and battery voltage during testing, so you can confirm your wiring matches the plan. View on Amazon

Common mistakes

  • Using panel nameplate watts instead of realistic output after losses.
  • Ignoring winter peak sun hours, which can cut output by half or more in northern climates.
  • Sizing the battery to the full nameplate capacity instead of usable capacity.
  • Forgetting that inverter standby draw runs all day and adds to your load.
  • Skipping the surge rating check for well pumps and refrigerators.

For a fuller worked example, see Off Grid Solar System Sizing Calculator: Step-by-Step Guide (2026). If you prefer a spreadsheet, Off-Grid Solar System Calculator Excel: Build Your Own Sizing Sheet shows how to set one up. Readers comparing system types can start with Solar Grid Tie System vs Off Grid: Which Should You Choose?

FAQ

How many peak sun hours should I use in a calculator?

Use the lowest monthly average for your location, usually the winter value, if you need the system to work year-round. Solar irradiance maps from national agencies list these figures by month.

Do I need a separate calculator for batteries and panels?

Most people use one sheet that links the load, battery and array sections, since each depends on the daily energy total. Keeping them linked prevents mismatched sizing.

Should a professional check my design?

Yes, especially for systems connected to household wiring or large battery banks. A licensed electrician or qualified solar installer should review the final design and wiring to meet local electrical code.

Conclusion

An off grid solar system design calculator is only as good as the numbers you feed it. Measure your real loads, use winter sun hours and build in losses at each step. Once your sheet balances, you have a clear parts list to take to the build.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our DIY solar power systems guides, checking product details against manufacturer specifications and owner feedback.