Updated November 2026
An off grid solar lighting system runs LED lights from a small solar panel, a battery and a charge controller, with no utility connection. In this guide you will estimate your daily lighting load, size the panel and battery to match it, and wire the parts together safely. The whole process takes a few hours of planning and works for sheds, cabins, barns and backup lighting around a home.
Step 1: Calculate Your Daily Lighting Load
Start by listing every light you plan to run, its wattage and how many hours per night it will be on. Multiply watts by hours to get watt-hours (Wh) per light, then add them together. A 10 W LED bulb running 5 hours uses 50 Wh per day. Five of those bulbs use 250 Wh per day. Add roughly 20 percent to cover inverter and controller losses and battery inefficiency.
Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).
Step 2: Size the Solar Panel and Battery
Divide your daily Wh by the peak sun hours at your location to find the panel wattage you need. If you get about 4 peak sun hours a day and need 300 Wh, you need at least 75 W of panel; a 100 W panel gives a safer margin for cloudy weeks. For the battery, multiply daily Wh by the number of days of autonomy you want (two or three is common), then divide by the usable depth of discharge. Lithium iron phosphate batteries are often rated for deeper discharge than lead-acid, so check the manufacturer’s specification before you size the bank.
Match the Voltage
Most small systems run at 12 V DC because LED fixtures and 12 V lamps are widely available. Keep the panel’s open-circuit voltage within the charge controller’s input limit, and make sure the controller matches your battery chemistry.
Step 3: Choose Fixtures and Controls
LED fixtures draw far less power than incandescent or fluorescent lamps, so they are the practical choice here. Look for 12 V DC models or use a small inverter for mains-voltage fixtures. A timer or motion sensor cuts waste, and many owners find it extends battery life noticeably. Use wire sized for the current: for short runs at 12 V, 14 AWG is typical for lighting circuits, and larger gauge is safer for longer runs.
Step 4: Wire the System in the Right Order
- Mount the panel facing the equator at an angle near your latitude, in full sun.
- Connect the panel to the charge controller’s PV input first.
- Connect the battery to the controller’s battery terminals, observing polarity.
- Connect the load (lights or inverter) to the controller’s load terminals.
- Install a fuse or breaker within 7 inches of the battery positive terminal.
- Power on the controller and confirm charging status before adding loads.
For a full wiring diagram with fuse positions, see Wiring Diagram for Off-Grid Solar System: A Step-by-Step Guide.
Parts Checklist
- Solar panel sized to your daily watt-hour need
- Charge controller matched to panel voltage and battery type
- Battery bank with capacity for your autonomy target
- LED fixtures (12 V DC or mains voltage with inverter)
- Fuses, breakers and correctly sized wire
- Mounting hardware and a timer or sensor, if desired
For a broader list, read What Is Needed for Off-Grid Solar System: A Step-by-Step Parts Checklist.
Common Mistakes and Tips
- Undersizing the battery, which leads to deep discharges and shortened life.
- Ignoring panel tilt and shading from trees or eaves.
- Mixing battery chemistries on one controller.
- Skipping fuses, which is a fire risk on any battery circuit.
- Forgetting that cold weather reduces lead-acid capacity and charging efficiency.
Recommended Gear
A basic multimeter lets you verify panel voltage, battery voltage and load current before you energize the system, which catches wiring errors early. View on Amazon
An inline fuse holder rated for your battery’s current gives the circuit protection the wiring diagram calls for. View on Amazon
A solar charge controller with a clear status display makes it easier to watch charging and load levels day to day. View on Amazon
FAQ
Can I run a whole house on an off grid solar lighting system?
A lighting-only system is designed for lamps and small loads, so it is not sized for appliances like refrigerators or heaters. For whole-home power you need a larger array, a bigger battery bank and an inverter sized for peak loads.
How long will the battery last?
Battery life depends on chemistry, depth of discharge and temperature. Lithium iron phosphate batteries typically last longer than lead-acid when cycled regularly, and manufacturers publish cycle-life ratings you can compare.
Do I need a permit or electrician?
Requirements vary by location and by whether the system connects to building wiring. Consult a licensed electrician or your local building department before installing any system that feeds permanent fixtures.
Conclusion
An off grid solar lighting system works best when you size it from your actual daily watt-hours rather than guesswork. Calculate your load, match the panel and battery to it, and wire the components in the correct order with proper fusing. With those steps done, you will have reliable light without a utility connection.
