Updated November 2026
To calculate off grid solar system size, you total your daily energy use in watt-hours, then size the battery bank, solar array and inverter to cover that load with enough reserve for cloudy days. This guide walks through each calculation with a worked example, so you can end up with a set of numbers you can check against real hardware.
Step 1: Total Your Daily Energy Load
Start with every device you plan to run. Multiply each device’s wattage by the hours it runs per day to get watt-hours (Wh). A 60 W laptop running 4 hours uses 240 Wh. Add up all devices, then add about 15 to 20 percent for inverter and wiring losses.
Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).
Example: lights 150 Wh, refrigerator 1,000 Wh, laptop 240 Wh, well pump 300 Wh. The total is 1,690 Wh, and with a 15 percent loss allowance the design load is about 1,940 Wh per day.
Step 2: Size the Battery Bank
Batteries store the energy you use at night and during low sun. Decide how many days of autonomy you want, usually 2 to 3 days in sunny regions and more in cloudy ones. Then divide the daily load by the battery system voltage and by the usable depth of discharge.
For a 12 V lead-acid bank at 50 percent depth of discharge and 2 days of autonomy: 1,940 Wh × 2 = 3,880 Wh. Divide by 12 V × 0.5 = 6 V usable, giving about 647 Ah. Lithium iron phosphate batteries allow roughly 80 to 90 percent depth of discharge, so the required capacity drops substantially. Check the manufacturer’s rating for usable capacity before you buy.
Step 3: Calculate the Solar Array Size
Your panels must replace the day’s energy use and recharge the batteries within the available sun hours. Use peak sun hours for your location, which you can find in NREL’s PVWatts or similar tools. Then apply a system derate factor of about 0.75 for temperature, wiring and charge controller losses.
Panel watts = daily load ÷ (peak sun hours × derate). With 4.5 peak sun hours: 1,940 ÷ (4.5 × 0.75) ≈ 575 W. Round up to the next practical size, such as 600 W of panels.
Step 4: Choose the Charge Controller and Inverter
The charge controller must handle the array’s current. Divide total panel watts by battery voltage, then add a 25 percent margin. For 600 W on a 12 V bank: 600 ÷ 12 = 50 A, plus margin, so a 60 A controller is a reasonable match.
The inverter must cover your largest simultaneous load plus surge. Add the running watts of everything you may run at once and confirm the inverter’s surge rating covers motor startup, such as a well pump or refrigerator compressor.
Planning Checklist
- List every device with wattage and daily run time.
- Add a 15 to 20 percent loss allowance.
- Choose days of autonomy and battery chemistry.
- Look up peak sun hours for your site.
- Calculate panel watts with a derate factor.
- Size the controller current and inverter capacity.
Common Mistakes
- Forgetting phantom loads from inverters, routers and standby electronics.
- Using peak sun hours from the sunniest month rather than the winter average.
- Ignoring battery depth of discharge and sizing to nameplate Ah instead of usable Ah.
- Skipping surge capacity for well pumps and compressors.
- Undersizing the wiring, which causes voltage drop at higher currents.
Recommended gear
A clamp-on power meter helps you measure real device consumption rather than relying on nameplate figures, which often overstate typical use. View on Amazon
A solar charge controller with a built-in display lets you confirm array output and battery state during your first months of operation. View on Amazon
FAQ
How many solar panels do I need for an off-grid home?
It depends on your daily watt-hour load and local peak sun hours. Divide the daily load by peak sun hours and a derate factor of about 0.75 to get the total panel wattage.
How many days of battery backup should I plan for?
Two days is common for sunny climates, while cloudy or snowy regions often need three or more. Longer autonomy means a larger and more expensive battery bank.
Should I consult a professional for my system design?
Yes, especially for battery banks, high-voltage systems or any work that connects to your home wiring. A licensed electrician or qualified solar installer can check your calculations and local code requirements.
Conclusion
To calculate off grid solar system size, work from your daily load through the battery bank, array and inverter, adding realistic losses at each step. Check your numbers against your site’s sun hours and the manufacturer’s usable battery capacity before you buy. For a deeper walkthrough, see How to Calculate Off-Grid Solar System Size: 7 Steps With Examples and Off-Grid Solar Power System Calculator: How to Size Your Setup Step-by-Step.
