Updated November 2026
A diy home battery backup without solar is a battery bank paired with an inverter and a charging source, usually the grid or a generator. It keeps essential circuits running during an outage and can be built with a few well-chosen parts. This guide walks through sizing the system, selecting components, and wiring it so it stays safe.
Step 1: List the Loads You Need to Keep Running
Start with the devices you truly need during an outage. Typical choices include a refrigerator, a few LED lights, a Wi-Fi router, a phone charger, and a sump pump. Note each device’s wattage from its label, then estimate daily runtime in hours.
Shopping for one? See our guide: 7 Best DIY Home Solar Systems with Battery Backup Compared in 2026.
Multiply watts by hours to get watt-hours per day. A 150-watt refrigerator running 10 hours uses about 1,500 Wh, though compressor duty cycles often make the real figure lower. Add a 20 percent margin to cover inefficiency. For more detail, see Solar Battery Backup Planning: Essential Loads and Safe Connections.
Step 2: Size the Battery Bank and Inverter
Divide your daily watt-hour total by the usable battery capacity. Lithium iron phosphate (LiFePO4) batteries are commonly rated for a usable depth of discharge around 80 to 90 percent, while lead-acid batteries are usually limited to about 50 percent. A 3,000 Wh daily load on a LiFePO4 bank therefore needs roughly 3,500 Wh of nominal capacity.
The inverter must handle your largest simultaneous load plus surge. Refrigerators and pumps can draw two to three times their running wattage at startup. Choose an inverter rated at least 25 percent above your continuous total. The sizing method is covered in DIY Solar Sizing Calculations: Panels, Battery Banks and Inverters.
Step 3: Choose Your Battery Chemistry
LiFePO4 offers more usable capacity per pound, longer cycle life, and steadier voltage. Lead-acid is cheaper upfront but heavier and less forgiving of deep discharge. Compare the tradeoffs in LiFePO4 vs Lead-Acid Batteries for DIY Solar. Whichever you pick, match the battery voltage (12V, 24V or 48V) to your inverter.
Step 4: Set Up Charging Without Solar
Without panels, the battery needs another charge source. Most builders use a battery charger connected to the grid, sized to the bank’s amp-hour capacity. A common rule is a charge current of 10 to 20 percent of the battery’s amp-hour rating. Some owners add a generator with an automatic transfer switch so the charger runs during long outages.
Your charger and inverter should be a matched pair or a single unit with built-in charging. Check that the charge profile matches your battery chemistry, since LiFePO4 requires different voltage settings than lead-acid.
Wiring checklist
- Install a fuse or breaker within 7 inches of each battery terminal, sized to the cable.
- Use cable rated for the current, keeping voltage drop under about 3 percent.
- Mount the inverter and batteries in a ventilated area away from living spaces.
- Install a transfer switch so the inverter cannot backfeed the utility line.
- Label every circuit and disconnect point.
Electrical work involving grid connections and transfer switches should be checked by a licensed electrician. For wiring basics, read DIY Solar Safety: Wiring, Fuses and Batteries.
Common Mistakes to Avoid
- Sizing for average loads and ignoring startup surge from motors.
- Using undersized cable, which causes heat and voltage drop.
- Mixing battery chemistries or capacities in one bank.
- Skipping a transfer switch and creating a backfeed hazard for utility workers.
- Installing batteries in a closed space without ventilation.
Recommended Gear
A clamp-on current meter helps you confirm actual loads before you size the system. View on Amazon
A battery monitor with a shunt shows state of charge and amp-hours in and out, which makes it easier to tell whether the bank is keeping up. View on Amazon
FAQ
Can I run a home battery backup without any solar panels?
Yes. The battery is charged from the grid or a generator through a charger, and the inverter supplies power during outages. Solar is optional.
How long will a home battery backup last?
Runtime depends on your usable battery capacity divided by your daily watt-hour load. A 3,500 Wh bank supplying 1,000 Wh per day would last roughly three days in theory.
Do I need a permit for a DIY home battery backup?
Many jurisdictions require permits and inspections for grid-tied or transfer-switch installations. Check local codes and consult a licensed electrician before connecting to your home’s wiring.
Conclusion
A diy home battery backup without solar comes down to three decisions: how much energy your essential loads need, which battery chemistry suits you, and how the bank will be recharged. Size conservatively, wire with proper protection, and have a licensed professional review any connection to your home’s electrical system.
