Updated November 2026
A diy solar irrigation system uses solar panels, a controller and, usually, a battery to run a water pump without grid power. In this guide you will work out your daily water need, size the panels and battery to match, and wire the parts in the right order. The math is simple once you have the pump’s numbers in hand.
Step 1: Calculate Your Daily Water Need
Start with how much water your plants need per day, measured in gallons or liters. A common rule for drip irrigation is about 0.5 to 1 gallon per plant per day in hot weather, but check your crop’s needs. Multiply by the number of plants or zones to get a daily total.
Shopping for one? See our guide: 6 Best DIY Solar Systems for Home Options Compared (2026).
Next, find the pump’s flow rate in gallons per minute and its power draw in watts. Divide your daily water total by the flow rate to get the pump run time per day. Then multiply watts by run time in hours to get watt-hours per day. That number drives everything else.
Step 2: Size the Panels, Battery and Controller
Take your daily watt-hours and add 20 percent for losses in wiring, the controller and the battery. Divide by your location’s peak sun hours (typically 4 to 6 in much of the US) to find the minimum panel wattage. Round up. For example, 1,200 watt-hours divided by 5 sun hours, plus losses, points to roughly 300 watts of panels.
For a battery, plan for about 2 days of autonomy so cloudy weather does not stop irrigation. Keep the battery’s usable capacity in mind; lithium iron phosphate batteries can typically be discharged deeper than lead-acid. Match the charge controller to the array’s voltage and current, with a margin of about 25 percent on current.
Step 3: Choose a Pump That Suits Solar
A DC pump running directly from a 12V or 24V battery is simpler and more efficient than an AC pump fed through an inverter. If you need AC, size the inverter to at least 1.25 times the pump’s startup surge, not just its running watts. Many small pumps draw several times their rated current at startup.
Common mistakes
- Sizing panels only for average sun hours instead of the worst month of the year.
- Forgetting pump startup surge when choosing an inverter.
- Using undersized wire, which drops voltage and wastes power over long runs.
- Skipping a float switch or low-battery cutoff, which can damage the pump when the tank runs dry.
- Mounting panels where shade from trees or structures hits them mid-day.
Recommended gear
- Solar charge controller with a load output: An MPPT controller with a built-in DC load terminal lets you run the pump and charge the battery from one unit. View on Amazon
- DC submersible well pump: A 12V or 24V pump runs straight from the battery and avoids inverter losses. View on Amazon
- Float switch: It stops the pump when the tank is full or empty, protecting the pump from dry running. View on Amazon
FAQ
Can a diy solar irrigation system work without a battery?
Yes, a direct-drive setup can pump only when the sun is shining, which works for filling a tank during the day. Without a battery, output drops with clouds and stops at night, so plan storage in the tank to cover those gaps.
How many solar panels do I need for a small garden pump?
It depends on the pump’s wattage and daily run time. Divide daily watt-hours by your local sun hours, add about 20 percent for losses, and round up to find the panel wattage.
Should I hire a professional for the wiring?
Low-voltage DC wiring is manageable for many DIYers, but any connection to household AC wiring should be handled by a licensed electrician. Check local codes before you connect to a building.
Conclusion
A diy solar irrigation system comes down to three numbers: daily water need, pump wattage and local sun hours. Work through the sizing steps, choose a controller that matches your array, and add a float switch to protect the pump. Start small, test the system for a few days, and adjust the panels or storage as your garden grows.
Related reading
- Top 7 DIY Off Grid Solar System Kits Compared for Homes (2026)
- Solar Panel Specifications for DIY Systems: What Each Number Means
- Solar Hot Water DIY: Build a Working System Step by Step
- Off-Grid Solar System Monitoring: A Step-by-Step Guide for DIY Builders
- Off Grid Solar System Setup: A Step-by-Step DIY Guide (2026)
