Updated November 2026

A DIY solar security camera pairs a low-power camera with a small solar panel, a charge controller and a battery so it can run without mains power. In this guide you will size the panel and battery for your camera’s real power draw, wire the parts together safely, and mount the system where it gets enough sun through the winter. The math is simple once you know two numbers: the camera’s daily watt-hour use and the peak sun hours at your location.

Step 1: Measure the Camera’s Daily Energy Use

Start with the camera’s rated current draw at its operating voltage, usually 12 V for most wired-to-battery models. Multiply current in amps by voltage to get watts, then by 24 hours to get daily watt-hours. A camera drawing 0.5 A at 12 V uses 6 W, or about 144 Wh per day. Check the spec sheet for both idle and recording figures, and use the higher number if the camera records continuously or runs infrared night mode, which draws more power after dark.

Shopping for one? See our guide: 6 Best DIY Solar PV Panel Kits for Off-Grid Builds (2026).

Step 2: Size the Solar Panel and Battery

Divide your daily watt-hours by the peak sun hours for your site, which you can estimate from a local solar resource map. If your site averages 4 peak sun hours, a 144 Wh load needs at least 36 W of panel output. Add a 30 to 50 percent margin for cloudy weeks and panel aging. For the battery, multiply daily use by the number of days of autonomy you want, then divide by the usable depth of discharge. Lead-acid batteries are typically limited to about 50 percent depth of discharge, while lithium iron phosphate batteries tolerate roughly 80 percent. A 144 Wh daily load with three days of autonomy on lithium needs about 540 Wh of storage, or a 12 V battery rated near 45 Ah.

Step 3: Wire the System in the Right Order

Connect the components in this sequence to avoid damage: battery to charge controller first, then the solar panel to the controller, and the camera to the load terminals last. Use an MPPT or PWM charge controller rated above the panel’s short-circuit current. Fuse the battery connection close to the battery terminal. Keep wire runs short and size conductors for the current, using a voltage drop calculator to stay under about 3 percent loss on the panel run.

  1. Confirm the battery chemistry matches the charge controller’s battery setting.
  2. Mount the panel and route its cable without pinching or sharp bends.
  3. Connect the battery to the controller, observing polarity.
  4. Connect the panel to the controller’s solar input.
  5. Connect the camera to the load output, then power on and check the controller’s display.

Step 4: Mount the Panel and Camera for Best Results

Face the panel toward the equator at a tilt close to your latitude, or steeper in winter if you want more low-angle sun. Keep it clear of tree shade between roughly 9 a.m. and 3 p.m. Position the camera for its field of view, and keep the battery box shaded and ventilated, since heat shortens battery life. A weatherproof enclosure rated for outdoor use protects the controller and wiring connections. If you want more background, see Best Solar Pool Heaters for DIY Installations: 5 Panels Compared.

Common Mistakes

  • Sizing the panel for summer sun only, then running dead in December.
  • Using a car battery without checking its usable depth of discharge.
  • Leaving the camera’s infrared or heater features on by default, which doubles the energy budget.
  • Skipping the fuse, which leaves the battery exposed to a short circuit.
  • Mounting the panel where a single branch shades part of a cell string.

A charge controller with a clear battery-type setting makes it easier to avoid overcharging, and many owners prefer models with a built-in display. View on Amazon

A weatherproof junction box keeps the controller and connectors dry through rain and snow. View on Amazon

A fused battery disconnect sits between the battery and the rest of the system, giving you a safe shutoff for maintenance. View on Amazon

For broader panel selection and wiring background, see Solar Panel DIY Projects: A Step-by-Step Guide for Beginners and Solar Panel Specifications for DIY Systems: What Each Number Means. If you prefer a packaged starting point, Solar Panel Home Kits Diy: How to Choose and Wire a Kit (Step-by-Step) covers what to check in a kit before buying. For mounting, Solar Panel Pole Mount Diy: Build a Sturdy Pole Mount Step by Step shows how to secure a panel against wind.

FAQ

How many watts of solar panel does a security camera need?

Most small wired-to-battery cameras need between 20 W and 50 W of panel, depending on their daily energy use and your location’s peak sun hours. Calculate it from your camera’s watt-hour use rather than relying on a general rule.

Can a solar security camera run through winter?

It can, but only if you size the panel for the weakest sun month at your site and add margin. Steeper tilt and a battery with several days of storage help during short, cloudy winter days.

Do I need a charge controller?

Yes. A charge controller prevents overcharging and deep discharge, both of which shorten battery life. Skipping it risks damaging the battery and creating a fire hazard.

Conclusion

A DIY solar security camera is practical once you know the camera’s daily energy use and your site’s peak sun hours. Size the panel and battery with a margin, wire components in the correct order, and mount the panel where it stays clear of shade. Consult a qualified electrician if you are connecting to a building’s wiring or are unsure about any part of the installation.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our DIY solar power systems guides, checking product details against manufacturer specifications and owner feedback.