Updated November 2026
An off grid solar system calculation PDF is a worksheet that turns your daily electricity use into panel wattage, battery capacity and inverter size. By the end of this guide, you will know the four numbers that matter, how to calculate each one, and how to lay them out in a document you can reuse. The math is simple arithmetic, but the order of steps matters.
Step 1: Total Your Daily Load in Watt-Hours
List every appliance you plan to run, its wattage, and how many hours per day it operates. Multiply watts by hours to get watt-hours (Wh) per day for each item, then add them up. A 60 W LED light running 5 hours uses 300 Wh per day. Add a 10% margin for wiring losses and appliances that draw more than their label suggests. For a deeper walkthrough of this stage, see Off-Grid Solar System Calculation: Step-by-Step Sizing for Beginners.
Shopping for one? See our guide: 6 Best DIY Solar Power System Kit Options for Off-Grid Homes (2026).
Step 2: Size the Battery Bank
Battery capacity depends on your daily load, how many days of autonomy you want (cloudy stretches with no charging), and the depth of discharge your battery chemistry allows. Use this formula:
Battery Wh = Daily Wh × Days of Autonomy ÷ (Depth of Discharge × System Voltage Efficiency)
Lead-acid batteries are usually limited to about 50% depth of discharge, while lithium iron phosphate (LiFePO4) batteries are often rated for 80% or more. Divide the result by your battery voltage to get amp-hours (Ah). A 3,000 Wh daily load with two days of autonomy and 80% depth of discharge needs about 7,500 Wh, or roughly 625 Ah at 12 V.
Step 3: Calculate the Solar Array Size
Your panels must replace the energy you use each day, plus losses. Peak sun hours are the average full-sun-equivalent hours your location receives, and you can get this figure from NREL’s solar resource data. Use:
Array Watts = Daily Wh ÷ (Peak Sun Hours × System Efficiency)
System efficiency typically falls between 0.75 and 0.85 once you account for charge controller losses, wiring, heat and dust. With 3,000 Wh per day, 4 peak sun hours and 0.8 efficiency, you need about 940 W, so a 1,000 W array is a reasonable target. Manufacturers specify each panel’s rated wattage, so divide the total by panel size to get the count.
Step 4: Choose the Charge Controller and Inverter
The charge controller must handle the array’s current. Divide array watts by battery voltage, then add a 25% safety margin. For 1,000 W on a 24 V system, the controller needs to handle about 52 A. Choose an MPPT controller when your array voltage is higher than the battery voltage, since it converts the surplus to usable charging current.
The inverter should be sized to your largest simultaneous load, typically 125% of the combined wattage of appliances you run at once. A 2,000 W inverter covers most small cabins where a microwave and a well pump will not run together. For how these parts connect, the Off-Grid Solar System Wiring Diagram PDF: A Step-by-Step Guide shows a typical layout.
Worksheet checklist
- Appliance list with watts, hours and daily Wh
- Days of autonomy and depth of discharge
- Battery bank Wh and Ah at system voltage
- Peak sun hours for your location
- Array watts, panel count and series/parallel layout
- Controller current rating with 25% margin
- Inverter continuous and surge ratings
Common mistakes
- Using nameplate wattage instead of actual run hours, which overstates or understates daily load.
- Ignoring the lead-acid depth-of-discharge limit and undersizing the battery bank.
- Sizing the array to average sun instead of the worst winter month.
- Forgetting inverter idle draw, which can run several watts around the clock.
- Skipping the 25% current margin on wiring and controllers.
Recommended gear
A basic clamp meter helps you measure real appliance draw, which is more accurate than label values. View on Amazon
A Kill-A-Watt style plug-in power meter records how many watt-hours a device uses over a day, which feeds directly into Step 1. View on Amazon
FAQ
Is there a free off grid solar system calculation PDF I can download?
Many solar installers and university extension programs publish free sizing worksheets in PDF form. Verify the formulas match the ones above before relying on any template.
How many panels do I need for a typical home?
It depends on daily consumption and sun hours, so a home using 10 kWh per day in a sunny region may need several kilowatts of panels. Run the Step 3 formula with your own numbers.
Should a professional check my calculations?
For systems that power medical equipment or a full home, have a licensed electrician or solar engineer review the design before installation.
Conclusion
An off grid solar system calculation PDF is only as good as its inputs, so measure your real loads and use conservative sun-hour figures. Work through the four steps in order: load, battery, array, then controller and inverter. Keep your worksheet updated as you add appliances.
Related reading
- Solar Off-Grid System Design Calculation PDF: A Step-by-Step Guide
- Off Grid Solar System PDF: A Step-by-Step Sizing and Wiring Guide
- Off Grid Solar Power System Wiring Diagram PDF: Step-by-Step Guide
- Wiring Diagram for Off-Grid Solar System: A Step-by-Step Guide
- Wind Solar Hybrid Off Grid System: How to Size and Wire One
